Plasma curtain
Wide-width treatment
A continuous plasma curtain treats the full width in a single pass. For panels, sheets and moving webs.
60 → 500 mm
Seven treatment widths
1 – 6 kW
Power depending on width
60 – 500 L/min
Gas flow, nitrogen, doped nitrogen
Modbus TCP/IP, RTU
Driven from your PLC
- Reply within 48 h from an expert
- Rental available to test on site
- Trials in our laboratory in Québec City
- Quote with no commitment
Technical datasheet, 2 pages, PDF
Dimensioned footprint, required utilities, protocols. To pass on to your integrator.
To treat a full width, without scanning
A panel before bonding
The whole surface must be activated evenly. Scanning leaves zones treated twice.
A continuous web
Treatment keeps pace with line speed. The curtain is sized on the web width.
Sheets at high throughput
Hundreds of parts an hour, all treated the same. The head is fixed: nothing varies from part to part.
See also
Every point gets the same treatment
The discharge covers the full width of the head. The part passes underneath: no overlap, no missed zone.
You choose the width to match your parts, from seven values between 60 and 500 mm. It sets the power, and so the generator: single-phase or three-phase.
Technical specifications
Installation at your site
Indicative values, confirmed during the study of your process.
- Floor footprint
- [x] mm
- Mass of the assembly
- [y] kg
- Extraction required
- [z] m³/h
- Protocols available
- [x]
- Cable lengths
- 3, 5 or 7 m
- Indicative lead time
- [y] weeks
Maintenance, consumables and warranty
- Electrode service life
- [y] h
- Replacement cost
- [z] $
- Preventive maintenance
- [x]
- Warranty
- [y]
- Rental possible
- yes
Frequently asked questions
How do I know whether this equipment suits my part?
Send us the part. We treat it in our Québec City laboratory. Within 48 hours you get the surface energy before and after, the settings used, and a frank opinion if plasma is not the right answer.
Has my material already been treated?
Materials qualified in the laboratory: [x]. Yours is not listed? That is the most common case. Send us three samples: a measured answer within 48 hours.
Can it be rented before buying?
Yes. You test the equipment on site, with your parts and your operators, before investing. Terms: [x].
What documents do you provide for a customer audit?
The process file: plasma settings, measurement methods, results on your parts and procedures. For regulated markets, it follows your sector's requirements.
And if no configuration fits?
We then design a custom reactor, matched to your material and your throughput. See the custom reactors →
To compare, or to complete
Whole surface
Surface source
A discharge spread across the whole electrode, treating flat parts and flexible films uniformly. No sweeping, so no over-treated band.
View the page →
Precise area
Compact torch
A nozzle that blows plasma straight onto the area to be treated, a few millimetres from the part. The most common way to activate a precise area.
View the page →
The complement
Test inks
A treatment you do not measure is not a process. The calibrated ink tells you in seconds whether the surface has passed the target threshold.
View the page →
Film deposition
Deposition station
When activating is no longer enough: a 1 to 300 nm functional film deposited by atmospheric plasma, anti-corrosion or anti-scratch depending on the precursor.
View the page →
Automated station
Turnkey cell
An enclosed cell with a Cartesian robot, plasma source and safety interlocks. You program a path, the station replays it identically.
View the page →
Millimetre precision
Precision torch
Cold plasma with a millimetre footprint, for small-area samples and sensitive substrates. It also accepts a precursor.
View the page →
To specification
DBD reactor
No catalogue configuration fits? Our experts design the reactor to your specification, dimensions and gases included.
View the page →As seen in
